Hi guys, haven’t posted on a while, but I am after some information on the adhesive used between the hatch mounting plate and 3rd brake light and the hatch glass itself.
also after info on alignment of the two.
I have removed them for pairing on my 84 here in Australia and as I finish up the...
Mmmm...not sure if it is the Fuel Pump Relay
Hi Wayne,
I am in Australia I have an 84 Coupe. I am looking at the wiring diagram for the fuel pump as it is the only one I can think of that has some of that wire combination.
Now the issue is that this relay is labeled Pin (A) Red 1.0 wire that...
Update on the install...
Hi Guys,
I have updated the videos on YouTube with the progress on my build.
Video 5 is the latest.
Anthony Walker
- YouTube
:beer
DeWitts Fan Kit
Now you can upgrade the factory 1700 cfm with our SP464 fan kit. The kit includes a SPAL high performance (2360 cfm) fan and Direct Fit adapter plate, ready to bolt on and the best part is, no cutting or splicing wires.
I don't have the SPAL part number as DeWitts actually...
Update: Blower Housing Install
Hi Everyone,
I re-installed the blower housing after its new coat of paint...5 coats of colour and 10 coats of clear...Getting better at spraying 2 pack paint.
I played around with the engine bay wiring harnesses over the weekend and tested the blower motor, the...
Finished disassembly on Blue's Engine
Finished disassembly on Blue's Engine.
Going in soon for chemical clean and sonic testing to see if its up to accepting a SCAT stroker assembly.
Check out this video I posted, this is the timing chain slop...it is the original baker-light gear and single...
Zora has been trade marked in Australia
This is a great story.
I did read that although GM was having trouble registering the Corvette badge in Australia, they had been successful in registering the trademark 'Zora'.
With local manufacturing coming to an end this year, and the acknowledgemt...
Couple of YouTube Videos
Hi Everyone,
A couple of Youtube Videos for your to check out the progress on Blue.
Video 1 - Underside of car:
Aussie 84 Corvette - Video 1 - YouTube
Video 2 - Topside of car:
Aussie 84 Corvette - Video 2 - YouTube
I hope that they can work through the Trademark Issues and finally bring the Vette here.
GM has already registered the trade mark "Zora" in Australia, but is having problems getting the Corvette's badge trade marked, as the boneheads here believe that the Chev emblem looks too much like the...
Hi Everyone,
I used a Dupont Paint Code (B8323) to mix up some medium blue metallic paint for my 84 Coupe here in Australia. While the new paint looks good on the chassis rails, against the current medium blue on the exterior panels, it looks like it has a bit of purple in it.
I had the paint...
Yes, but the firewall is changed during the RH drive Conversion
The engineering company that does a lot of RH Drive conversions here in Australia, removed the original firewall on the C4's during conversion...C5 and C6's all have the body conpletely removed...I believe that the C7 is the...
Thanks Roy
I didn't get a chance to take a happy snap on the weekend, I was busy with the cabin wiring for my FAST EFI install...
When they changed to RH drive and compliance for Australian Design Rules, they replace the two outer brake lights with amber lenses and convert them to indicator...
Ok...here is is...
So the relay is a normally open (NO) double throw relay.
Terminals are:
86 Trigger wire is the factory purple ignition wire
85 Is and earth/ ground wire
30 Looks like a power feed - my guess is battery direct.
87 & 87A - Only one is used but I assume it actually feeds the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.