Welcome to the Corvette Forums at the Corvette Action Center!

Recent content by eRiCdWoNg

  1. E

    Passenger mirror goes haywire with "memory"

    Thanks for the reply. This is what it came up with: B2293 H B2285 H B2263 H B2265 H U1064 H I should also mention, that when using the keypad adjusting the mirror LEFT or RIGHT it will only move a few degrees if I hold it down. I have to let the button up and press it again to keep it going...
  2. E

    Passenger mirror goes haywire with "memory"

    Need some help with this one, when I press "memory" on my door the right mirror will aim towards the left. If I press it again it goes to the left some more. This happens every time I put the key in the car with the door closed as well, so I have to redjust the damn mirror every few times I...
  3. E

    P0441 EVAP system no flow during purge

    Help, I have this code and have no idea how to bust it. I'm pretty good with electronics etc but this one's got me. I've so far found this info: Circuit Description The EVAP vacuum switch is a normally closed switch connected to ground. The EVAP vacuum switch is mounted in the vacuum line...
  4. E

    Adding Active handling to non-AH car

    ...when I bought my car this was one of two things I overlooked. Active handling and the HUD. THe HUD I can add, but I really dont care about that too much as it really doesnt make the car perform any better. I'm fairly handy, I'm all about projects so I'm wondering if this is possible...
  5. E

    Help, disconnecting "quick disconnect" from clutch slave/master...

    Ok this ones got me, I bought the 5/8" FORD fuel/AC disconnect but its just slightly large. What am I doing wrong? What I'm doing is on that brass cylinder looking thing, pushing the white plastic part that faces the front of the car towards the rear of the car, but it isnt "popping" off like...
  6. E

    Inspecting a 2000 Coupe - What am I missing?

    Hmmm, also make sure power windows/locks and seats all work. Also make sure oil pressure level isnt pegged (bad oil pressure sensor). Check inside of tail pipe for oiley residue (oil consumption). Make sure all tire pressure sensors work. See if theres any evidence of leaks. Make sure...
  7. E

    DIY MN6 transmission rebuild

    Hi, yes if you could send that that would be great, ericdwong@aol.com I will also share my experiences with rebuilding the trans.
  8. E

    DIY MN6 transmission rebuild

    ...Since I gotta yank my driveline to service a leaky slave cylinder, I'm going to rebuild the transmission. My 3rd gear grinds during hard shifts as well as when it is cold out. And, I have the infamous leak. I'm assuming its the input shaft but I wont know for sure until I yank the thing. I...
  9. E

    Removing/inspecting HVAC fan?

    Well it was very easy, only 3 bolts. Anyway there was leaves in the blower motor. I removed the leaves and now it is just fine, no more squeek! Yay...
  10. E

    Removing/inspecting HVAC fan?

    ...I havent peeked down there yet but thought I'd ask here, how easy is it to get to the HVAC fan so I can inspect it? At the minimal setting, it squeeks and if I turn the fan off, it stops so this leads me to believe its the fan. Hopefully I can cure it with grease but if not I"ll replace the...
  11. E

    Front Parking Lights always on - What's That?

    I dont like the pull the fuse method- you wont have the approach lights. Here is a better method that still allows the fogs and rev. to come on. http://www.corvetteforum.com/techtips/viewsubtopic.php?SubTopicID=273&TopicID=1
  12. E

    Do not have run flat tires - What do i do if i have a flat

    The Z06's do not come with run flats OEM... I also dont use run flats. If someone slashes my tires or if I have a blow out, yes I'm screwed.
  13. E

    Clutch pedal got stuck 2x in one day!!!

    Well I went to the garage, checked my stuff and guess what the master cylinder was dry as a bone. Hmmm. This means I have a leak. I wonder where that came from, I never see anything on the garage floor but then again the entire system doesnt have too much to begin with. This might be good...
  14. E

    Clutch pedal got stuck 2x in one day!!!

    ...never done it to me before twice in a day. I got out of work around 5:45ish, got to parking lot and went to pull back and it was fine at first then boom, the clutch felt like it released, had no tension and I was stuck. Bout 15 min later after banging it around it somewhat returned enough for...
Back
Top Bottom