Search results

I dont believe I have any bearing issues, the car runs super sweet, but just recently I noticed when I first start the car it sounds like it detonates, I replaced the distributer cap that was badly cracked.. it started a few days after I had the new cap on.. I have a msd ignition, I got another...

thanks.. I am going with the fan that flattens out. I have an electric fan, I hook it up, to a temp switch, incase there is a problem with high temps. I had this flex fan for about 17 years.. that should be a record.. no problems with loose blades just doesn't cool enough. I changed the front...

I have a flex fan now, it's pretty useless, it's the one that has the real small blades. my car runs in the 200-210 range I want to replace it with either the FLX-1318 (summit)or the 771-85180 (jegs) summit's flattens at high rpm.. jegs flows more air at all rpms.. in the real world just how...

76L82.. thanks for the compliment. you can check out www.smartshoppersinc.com you can see the kirker complete paint kits.. when you apply the clear just mix enough to do one coat at a time. it dont seem to have long pot life.. I dont know where in Maine you are I'de give you a hand, but I am...

this is way to funny on these little imports... I get a big laugh when I see one with a moNster tack, it takes up most of there dash.. they throw on a muffler, and they think there mad max behind the wheel..;LOL TO tell you the truth, I wouldn't even race one, why give them the luxury of drag...

LanceB.. I really doubt, that you could come even close with a rice burner.. not to offend, but I know I ate a 600cc ricer, and thats not a stock (im my vette) motor.. most guys got the 750cc or higher.. these bikes are super quick.. I had a GSXR-1100 back in the day.. jump on one, and you'll...

cfour93.. yes, I replaced the cap and rotor, the wires have only a few thousand miles on them, there accels 8.8 I have a msd ignition with an ajustable timing control inside of car.. everything is in order.. I have not yet pulled a plug to see what it looks like... but will if needed..

recently I noticed my cars popping through the carb, it got pretty bad. I had a clear distributer cap, come to find out that the cap had a lot cracks in it, just about everywhere.. and the rotor tip was loose, almost ready to come off.. when the car first starts there is slight popping from the...

cfour93... thanks wishuwerehere82....you must be bored to post that:eyerole

I tried a screw driver, but the screw end is square.. no way that I can gues if it turns or even be acurate, but thats a good link. thanks

maybe I should post a pic of the carb, that will help.. http://

hi guys.. need some help here on my sons car, does anyone have a pic of the tool thats used to adjust the mixture screws on and edelbrock carb, the screws appear to be square..

believe me when I say I am regretting this.. I was thinking a little less power taken from the motor on the high end.... yea I know, what 10hp....

thanks

can I adjust the advance on the distributer? where the vacume advance canister is on the distributer, I believe you can adjust it with a allen head, not sure if this is true, or wich way to turn for advance and retard... it's an after market electronic ignition.....

maybe my bad luck, but I got 2 holley regulaters and 2 fuel pressure gauges, and I still have the needle jump up to 12-13lbs when I rev the engine.. is there a way I can change the spring or something in the pump to regulate fuel pressure, it's the holley blue pump.

a pic of the door would be great to see, looking forward to seeing it, I think I'LL be getting one and install over the winter, I got my two boys to help..lol..

thanks andy

what was the cost of the kit?? and where did you get it?

this is what I would like to do...http://