Search results

It is time to install new shocks on the 90. Would like input on a couple options. Monroe Sensa-Trac and the Monroe Gas-Matic . I understand the Sensa-Trac, how it works etc. How well do they work on the Corvette? Same question for the Gas-Matic. Any preferences and why. KBY shocks are they...

I would like to buy a throttle body to fit a 90 L98. One with worn throttle shaft bore would be ok if cheep enough,actually perffered. I am a machinist and want to bore and sleeve one. PM me if you have one to get rid of. Glenn :w

I think I finally figured out why my 90 idles to fast most of the time and now and then searches. I noticed the other day that coming to a stop sign it hardly dropped below 1600 rpm. I burped it and it settled down to it's near normal (for this car) idle speed. Back in the garage I played with...

Has anyone here had any experience with ZF problems? Mine sounds like it goes part way in gear or not all the way out. Shifter feels just a little spongy is the easiest way to describe it. Are there any known problems with the shift linkage or the forks ? Glenn :w

Any one know where to get a left rear marker light assembly for my 90? Glenn :w

How do I locate a vacuum leak on the L98 if I have one? Glenn :w

Started work on my new exhaust from the cat back. Got the pipe done now need to work on a couple mufflers. The pipe is 3 in OD 304 food grade stainless. I bought some elbows we use at work and cut them to the right angles. laid everything on top of the old pipe and matched it all up.Tacked it...

I spent a few hrs searching here and with Google and can't find the type of information I want. Three yrs ago I discovered 2 bad injectors when I was replacing the intake gasket. At the time money was tight so I only replaced those two from a local parts house. The box was red and said Standard...

Replacing the clutch on my 90 this week. Couple things I am not sure of. 1- Do I have to remove the distributer or the cap and rotor only? 2- The service manual mentions a sealer for the support beam. Is this important ? 3- What do I use to remove the pilot bushing? Thank you Glenn :w

I have to finally put the clutch in my 1990. Is there a good place online to buy the clutch kit and Dual Mass flywheel? I am thinking I might want to stay with LUK. Is this the wise thing to do ? Thank you for any suggestions. Glenn :w

Don't know if this has been posted before but just had to share it. http://thefiftiesandsixties.com/CarsWeDrove.htm Glenn :w

The clutch on my 90 slips. The thing that is confusing me is that it is inconsistent. At times I can hammer it through 1st and 2nd with no perceptible slippage and some slight slippage in the mid range of 3rd . At times it will slip with the slightest acceleration. My experience with clutches...

I have an 89 Riviera with a heater problem. One day I couldn't control the heat , couldn't turn it off. The following day the heat was gone. Air cond. works. I checked under the hood and all vacuum lines seem to be intact.I really don't want to dig into the dash without some info on it. I hope...

I would like feedback and experiences with this brand cluth. I need to buy a settup for my 90 vette. I was told some things about this brand that I will share a little later. Thank you Glenn :w

I ended up with a really nice set of 1990 ZR1 wheels. SCRATCH THAT THEY WERE NOT WHAT I WAS TOLD Glenn :w

I finally got the luggage rack mount built. It took some time to get things right but I think I am there. I made brackets to clamp to the back frame crossmember to mount the rear of the assembly. Without a reciever attatched everything is invisible from the rear. I have threaded bushings...

Does anyone have a trailer hitch installed on their C4. If so I would like to see some pictures of how and where it is mounted. Measurements would be helpfull. I have found a picture of one online but no way of knowing how they mount it.I want to build a bracket for a luggage rack out the back...

I am looking for a set of wheels for my 90. I believe the right side are both bent and if I can buy right sides or a full set reasonably I would do that rather than hassle with having them straightened. Finish is not important as long as there are no chunks missing. They must be guaranteed to be...

The weather has been very mild, with little additional snow. The snowbank in front of the corvette stall melted away. The roads are dry for the most part, so yesterday I took her out. WOW! I only took her for about 30 miles total but I think now I may survive the winter. I had a nice flat...

Has anyone else come across Red Tek 12 A? It is sold as a replacement for both R12 and 134A without any conversion. It can be added to either without any problems. I bought a case of 12 -12oz cans for $95. Any feedback on this would be apreciated. Glenn :w