Search results

For 88 Can these be replaced without dropping the tranny? Any insight or instructions on how to do it appreciated. Looks for similar threads but didn't find any.

For 88. Testing vacuum prior to R134 conversion. The valve is audibly leaking in the line that goes from condensor to evaporator. It appears to be a Schraeder valve but seems to be bigger than the one on the accumulator (drier). Is it a Schraeder valve? It doesn't engage with the same removal...

Radiator baffle side bracket mounting Anyone have any pictures of how the radiator mounting brackets mount to the shroud? I understand the mounting of the center braces but could use a little help on the side brackets. Please advise

For and 88. Anyone dealt with this issue before and what did you do. Please advise. http://i295.photobucket.com/albums/mm149/mdwood1/DSCN1648.jpg

Anyone have any recommendations. Looked all the places I know and not finding one. Tired of reworking the one I have.

For 88 coupe Getting ready to paint and upon removal of front bumper assembly saw that the frame extension that the bumper mounts to is damaged. Looks like car was in front end collision as its bent up a bit. Is it hard to replace this part? Is it removed and replaced with just bolts or is...

For 75 coupe Just got wacked by a rock on original windshield and it cracked. Can I get these stickers anywhere?

For 75 but with big block installed, A/T MSD 6000rpm limiter Holley 670 street avenger performer 2 intake 650 rpm idle in drive, 800 rpm idle in park Runs well except when throttle is first applied normally from a stop. Engine sags and almost dies. changed acclerator pump dicharge nozzle...

88 stock manual transmission with overdrive Working fine this AM then suddenly no 1st or 2nd gear. No resistance when shifting into 1st or 2nd. Transmission wont engage in 1st or 2nd but will in reverse 3rd and 4th. Normal resistance when shifting into Reverse, 3rd, or 4th. Took console...

for 75 coupe Do I need to remove the windshield trim to get the T bar that covers the top center support off?

Requesting a little advice on which primer to use on new SMC valance. From searches I've gathered that epoxy primer will do the trick but are there recommended products by tradename. I can't tell from label which ones work on SMC or are epoxy based. Please advise.

Any tips or trick to removing and installing a 4+3 overdrive?

Obviously 1988, but what years of overdrives will work in 1988 without major mods? For example, will a 1986 OD work in 1988, what modifications would be needed to make it work?

Still trying to remove frozen striker. Tried penetrating lube with pneumatic impact driver, and impact driver with dead blow hammer. No luck. Any advice? Are there any photos of what the back side looks like so I can have a clue what's going on behind the fiberglass. Or any advice on...

4+3 OD just went out. Dilemma is whether to rebuild 4+3 or put something else in. 4-speed section is in verygood condition. Its for a 35th anniversary so I think I know the answer to preserve value but just gutchecking to see if another option wouldn't knock the value down too much 80K...

Having trouble discerning if the +40 -40 ammeter gauge or the 0 to 18 volt voltmeter is the correct gauge for a 75. I have found both available but don't know whick is correct. Any advice is appreciated!!!!

Passenger side door striker is siezed up and wont loosen opr tighten with penetrating oil and all the nudging I can give it. What is the smartest way to get to it to examine, remove, replace it?

I'm working on a 75 that originally had A/C and a 350. Now has no A/C and a 454. Heater controls don't seem to get any response out of heater box. Fan switch works but blower doesn't. Vacuum lines appear to be in good condition. Seems like vacuum switch is functioning, but I am obviously...

1975 with a 454 installed. Original car had air conditioning but 454 wasn't installed with it on. I want to retrofit it but don't have original parts from original matching 350. Need advise on aftermarket A/C vs. restoring A/C from say a 74 454 set up. Have original condensor, no VIR, all...

Where can I find the best value when replacing 35th anniv. seat leathers? Any advice would be appreciated.