Welcome to the Corvette Forums at the Corvette Action Center!

Search results

  1. E

    700r4

    I need to replace the plug on the lockup actuator as the three wires pulled out. I have bought the plug but need to know which wires go where? Also it used to lock up but the car has sat and now will not lock the converter up do I need to replace the lockup switch and how hard is it to do...
  2. E

    Part # from zip corvette help anyone?

    Looking for part# for anti rattle door window bumper to order from zip corvette cant seem to find on websight . I dont have the catalog . Thanks Ethan oh on a 91 Vette.
  3. E

    Wont start

    wont start Yeah had that tested was good even put in a old one I had still would not start think both could be bad?
  4. E

    Wont start

    I have a 91 Vette. Was running in the drive way then just died and will not start. Has voltage to dist. replaced coil and the little black unit in the dist. No fire out of spark plug wires, anyone ?
  5. E

    LT4 LT4 Hot Cam Kit ('90 L98)....Opinions? Quality?

    Lt4 Hot My uncle is s mechanic he helped me change the springs and put new umbrela valve seals in we checked for coil bind and had plenty of clearance with the kit. The only thing I did not mention was I had to order custom length push rods as with the extra lift and 1.6 rockers the roller...
  6. E

    LT4 LT4 Hot Cam Kit ('90 L98)....Opinions? Quality?

    LT4 HOT ON l98 I have this setup on 91 Vette with 2400 B&M stall this thing pulls like a SOB it will pull strong over 6000 rpm. I have big mouth intake Arizona Speed & Marine Big tube runners with ported plenum and 52 mm throttle body. Bought from Scoggins Dickey Chevrolet just ask them to set...
  7. E

    Timeslip of a 13.384 run on stock TPI!

    Timeslip of 13.38 WOW I cant wait to see what my 91 will do with LT4 Hot kit and high flow upper goodies. Right now has 2.59 but plan to buy 3.54 also has B&M 2400 stall pulls hard to shift point of 6 grand not bad for a TPI engine.
  8. E

    Ed Wright Chip

    I have a 91 Vette w/Lt4 hot cam kit/Big mouth tpi base /ASM runners/ported top w/ASM52 mm throttle body/also w/all cheap free mods. I changed injectors to motorsports 30lbh cut pressure down to 35 .The engine was so rich it would not run . I bought a Ed Wright chip this helped at least it runs...
  9. E

    Cheapest place to buy new Optispark

    Need new opti for 94 Caprice has the vent hose on it so I quess it is the later 95 model? Any one know the cheapest place to get one.
  10. E

    When have you checked your spare tire last...???

    Spare Spare ! I dont need no stinking spare.:J
  11. E

    oil leak

    oil leak fixed (well so far) Twas the intake again well cleaned it off good with carb cleaner squeezed some (Pam Anderson enlargment goop) silicone in and whalla that with a new pcv I think did it for a while. Well anyhow that Lt4 hot kit really makes the ole L98 scream. Adjusted the 700r4 to...
  12. E

    Changing rear to 3.73 from stock

    3.73 complete rear Hey Wookie if you dont mind what was the cost and where did you get it from? What was your previous gear ratio? I'm looking into buying complete unit with 3.45 or 3.54 ratio.
  13. E

    Erratic Coolant Temperature Readings!

    Temp reading Check for air in system all Lt1,s had two bleed valves that you loosen with the engine running that will bleed off air in the system loosen them one at a time air will come out then a steady stream of fluid. Maybe will cure your problem?
  14. E

    Problems, problems and more problems

    oil leak Well budy seems we have oil leaks in common. Mine was and still is the intake rear end seal. While I replaced this said to myself good time to go to the LT4 hot cam kit. Well got through headache and I do say HEADACHE! Now quess what the same oil leak same spot so here we go again...
  15. E

    oil leak

    Well here we go again pulling the intake off again seems the back seal (silicone) sorry if spelled wrong dont have Pam Andersons phone # to get correct spelling.Any how back intake seal is leaking again .I dont get it , it has squeezed out at least half an inch but still leaking.It,s a...
  16. E

    oil leak

    Anyone have a oil leak on there 91? Has anyone heard of a head gasket leaking or blowing out on the driver side back where the oil drain back hole is?Or anyone had the oil galley plug under the driver side head leak. Already replaced intake gasket,valve cover gaskets,both oil sending units also...
  17. E

    fuel pressure

    help anyone?
  18. E

    How hot does your c4 run?

    Coolent temp Correct me if I,m wrong but I thought on a 93 down the fan turn on was controlled by the sending unit not the computer like 94 up where you can reflash the computer. On my 91 all I did was the 160 thermo and it never gets over 180 no mater what?
  19. E

    Need a little advice,PLEASE?

    86 L98 You might just get lucky when you pull the intake but maybe not I think 87 was the first year for roller cammed blocks. Check the lifter valley for three threaded bolt holes to hold down the lifter retainers that keep them from turning on them cam lobe. If you have this setup you can use...
  20. E

    91 rear gears or switch to Dana44

    91 rear gears If you dont mind ask your bud how much dough to switch to 3.54 in the dana 36.If I can get a used dana 44 out of a six speed car with 3.45 Ill go that route . It,s fixing to see lots o strip time. :):eek
Back
Top Bottom