Welcome to the Corvette Forums at the Corvette Action Center!

Search results

  1. 6

    What Head To Use?

    Ok I have a 68 verty with a 350 with reall crappy heads. Looking to put some aluminum heads on it but not really sure what I should get in the means of specs. Its a 4spd with a Holley 650 carb and here are the cam specs. lemme know what you all think! cnpgalea@yahoo.com Basic Operating RPM...
  2. 6

    1970 LTI 1 Oil Pan $$$

    can anyone tell me what an original 70 LT1 oil pan is worth? I have an engine Im parting out and a guy wants the pan but no idea what its worth. Thanks Chris
  3. 6

    1970 LT1 3972110 INTAKE FOR SALE

    I have a 3972110 intake and 3991492 heads for sale on ebay right now with some other parts. Intake item number is 180121160646.
  4. 6

    68 Cooling & Fan Shroud HELP!

    Going to put a 180 stat in it and get a spacer for the fan to get it inside the shroud if I can, if not then I'll have to see how much the shroud extensions are that I hear people post about. The guy who built the car was very meticulous and Im sure all the seals are there, I know I saw one...
  5. 6

    68 Cooling & Fan Shroud HELP!

    So what is normal operating temp and max operating temp? Maybe Im just paranoid but Im just not use to having a car that runs this hot . . .
  6. 6

    68 Cooling & Fan Shroud HELP!

    Sorry Bob forgot to answer your questions . . . it was mostly go . . . not alot of stopping. It was very hot and humid though, had to have been near 90. I replaced a 69 396 Chevelle with this vette and I had a 2 core (2 cores but each was 1 inch wide) aluminum rad for it and it never got above...
  7. 6

    68 Cooling & Fan Shroud HELP!

    http://www.snapfish.com/thumbnailshare/AlbumID=23951869/t_=26991973 Here is a link with pics showing the fan and shroud
  8. 6

    68 Cooling & Fan Shroud HELP!

    Hi all . . OK hopefully someone can help me out. My 68 with a 350 I just purchased recently is having cooling problems. Up here in MI this past weekend it was pretty humid and hot, took the car out to have a paint match done on it in normal driving and it goes up to 210, maybe slightly higher. I...
  9. 6

    LT1 Hood, who makes the best repro

    Been looking for an original LT1 hood without much luck. What is the BEST repro LT1 hood available??
  10. 6

    LT-1 Hood Needed in Michigan

    Im looking for an LT-1 hood within 2-3 hrs from SE Michigan. Would like one in very good - mint condition with the exception of just needing paint. thanks everyone Chris cnpg@comcast.net
  11. 6

    Breaking Up at WOT

    A friend had the same thing happen to his 6.6 T/A, but his was fine at idle or low end but when he mashed it . . . fell flat on its face. He swore up and down his wires were fine until I told him pull the car in the garage with the lights out and start it up and rev it . . . . it looked like a...
  12. 6

    I Think my Head or Intake Gaskets are Shot

    After a head gasket experience with chrysler with a 2.2L in it that plugged my entire system and rendured the car pretty much useless and a brother in law who tried one of those motor flush products I'll never ever in a million years ever dump anything like that in my oil or coolant. The brother...
  13. 6

    I Think my Head or Intake Gaskets are Shot

    Never ever trust or think any of that "Mechanic in a Can" stuff will work. All any of that bars leak stuff will do is plug up more of your system since its passages are probably much smaller than new just from normal use.
  14. 6

    1968 Corvette Convertible

    What did you want for the car?
Back
Top Bottom