Search results

I have power brakes, I will keep on bleeding the system. Would the power booster have any effect on the pedal. I may just get I may just get a friend to help and bleed the brakes the old fashion way, thanks for all the help on this.

just finished replacing the caliber. Now all 4 are new. started to bleed the system again and still can not get a hard pedal. I will continue to bleed the brakes I do not see any leaks or fluid on thre gtround . I filled the master cly I will check it in the Am if there are any leaks I should...

Just took of the back calibers and you were correct they were also leaking. I will hopefully install new caliber tomorrow and bleed system again. Thanks for all your help.

I am using a one man bleeding kit and it sucks the fluid out. I always see some air bubbles can the kit be suckiing air through the pistions on the calibers ?

After bleeding the master cly and back brakes went to the front and replaced the calibers bleed the front and when i steped on the pedal it was hard. Started the car and no more pedal it went to the floor.. Should I change the rear calibers ? could they be sucking air I do not see any leaks? The...

Mike, Thanks I have followed your instructions. Pulled the front wheels off and found that the calibers are leaking, I did bleed just to see if I would get pedal and I did. Of course goes to the floor if I stand on the pedal. Going to buy new caliber now. Thanks again to all..

I Did bench bleed the master and I also followed the bleeding sequence right rear than left rear.. I though I would get some pedal after the two but there is no pedal.. I will get to the fronts in the AM.. Thanks

chuck, thanks for the info. Just got the car it was sitting in a garage for about 10 years no brake pedal at all. first thing i did was change the master clyinder. I will bleed the fronts tomorrow.

I am having a problem bleeding the brakes. I have bleed the backs inner and outer with no improvment in the pedal. It goes to the floor. Do I need to complete all 4 before I see any improvement? Or am I doing something wrong. I am useing a one man bleeder kit and it seems to work well I have...

My gas gage is spiked to the past full on the gage. When I start the car the needle move up about 1/8 of an inch. I looked for an open ground with no luck and now think the sending unit is bad. Is there any way of checking the sending unit without droping the tank? Or is there other things I can...

Heard a ticking for a few weeks finaly took off the valve cover and discovered that one of my push rods was just sitting in its slot with about 1/4 in of the rod above the head. What has happened? did the lifter become dislogged from its seat? The rocker arm is just hanging and is not connected...

THANK YOU VERY MUCH... Looks like I should be able to get things working.

That you very much.. I will check these two items.

Both stopped.. Thanks for the reply

My power windows just stopped working. Can someone tell me where I can find the pwr window relay and the 30amp ckt breaker. Hope it is one of these or a ground wire.

My power window just stopped working. Where can I find the power window rely and the 30 amp ckt breaker? Hopefully it is one of these or a ground wire.

I live in Fairfield, NJ just down the road.. I have a 77 and I used a guy in Dumont.. He is good AND VERY RESONABLE. E mail me at johnrem46@aol.com .. John

Thank you Vette79 and Duke94 for your responce. They where very informative and helpful with my issue. It seems that the fireberglass fender seperated from the inner fender. Not the mount. I did notice that the mounts are pretty worn and rusty.,. Was it very difficult to replace them? Thanks for...

1977... The bottom of my left front fender is loose. It can be pulled away from the body mount just before the the drivers door. I looked under the car and it seems that the mounting bracket pulled away from the body . The bracket still seems to be attached to the mount. I know I will have to...

can anyone tell me what color blue the 1977 covette engine is? I tried the 6 cly blue but it is to light.