We are buying a New House and needed the money I can live in a New home But I can live in my old C4 Sorry family comes first.
It been adventure thats for sure.
Next project will be a 34 Vicky but this be a whlie a long while.
:w:w:w
I was chasing a knocking sound in my Vett for a while now it’sbeen tracked down to the Fuel Pump Regulator.
It holds 43 PSI of pressure at Idle But as soon as you turnthe engine off it drops to Zero.
It has almost NEW FIC Bosch III 24# injectors and same forthe Fuel pump a Walberg 190...
I been trying to find a tapping sound the motor has about 7000 miles on it CC Ultra Magnum pro Steel full roller arms.
The rocker arms do make some noise but this not where the noise is coming from.
I replaced the roller lifters with GM LS7 lifters, Put new push rods in it just in case checked...
I have Thrush 2 chamber Muflers now wifes says they are to loud.
There just as loud as Flowmaster 40"s..
How Loud are Borla Stinger cat back Mufflers compaired to Flowmaster 40"s.
And how are the standered 2.25 Borla direct fit mufflers.
I also had a set of Magnaflow's they 2.25 they were to...
If I remove the EGR tube that runs from the Exhaust manifold to the intake manifold where it hook to the EGR temp swicth what will happen..
Will this throw a code or what I will keep the EGR temp swicth in place hooked up if needed just caped off.
The reason why I asked this I using a small hard...
Who has the best deal on Data Log Cable.
I seen diffrent types I dont know if it matters or not.
I do need to down load a data log out my 86 so I can get the chip fined tuned I would like to find out how to do myself would be very nice also.
I have No idea what involded in this stuff I wish...
I tried to pass California smog today it failed The smog technician said it runs lean at Idle but still passes there but a cruise it fails it too rich at 2500 RPM’s.
He said it could be my fuel regulator When I got home I hooked up my pressure gauge reads 40 PSI at Idle 38 PSI at 2500 RPM’s...
I think I have all my oil leaks Fixed but for one.
After reading other Thread about main seals leak and Dont use Fel-Pro Main seals for rear main seal form Pete K.
And yes thats what I used when building the motor he said use just about any other brand But Fel-Pro he has a track record of them...
My Brake Master cylinder is bad on my 1986 I started toprice a replacement so far at Napa a new one $240.00+ a rebuilt $150.00 arebuild kit $130.00.
Yes I also thought it would been cheaper what other yearscan I use that will bolt up or Is there an aftermarket High performance one that willbolt...
I have to pull the Trans AGAIN but this time it for aLeaking Main seal Oh what fun I know.
I was thinking Might as well put a Higher stall convertor inI have a 2500 Stall now behind the 383.
It works but it could use more stall more grunt out the Hole.
I have been thinking of a 3000 Stall but...
Stupid Grin.
I installed my 383 about 7 or 8 months ago been tweaking in every chance I can getting it fined tuned including chasing oil leaks coolant leaks the ones you can’t see where it’s leaking but what under the car when you move out of the garage to take it for a spin you see the spot on...
The other day going home one of my Co-works was behind me and he told me when I got on gas he said there was Black smoke as I pulled away from him.
I have a 383 with LT4 hotcam PCMforless tune.
The car is tuned for my set up but is this normal I was concern I could been running to lean at...
Just curious which roller rocker arms are you using.
I using Comp Cams Ultra Pro Magnum 1.6 Steel Full roller rocker arms.
They cost a little more but at least I don't have to worry about them breaking on me after all those cycles of as a DD.
Anyone using or tryed Flow Master 10 Mufflers on there C4.
I tryed the muffler eliminators love the tone at Idel but anything after that to loud for me sounds good but got old fast.
I have a Magnaflow 2.5 cat back system now an it to quite for me I looking for more Roar but not aas loud a...
I had this Upgrade cooling fan Relay for my 1986 Vett for a while now so it is time to install it.
But It did not come with any wiring schematic for the old or new how to rewire it to the new plug.
I looked at my Chilton But iy dont tell me nothing.
What wire what in the car as in color.
I...
The car has done this before the EGR cross over going though the intake manifold is starting to have a leak at the gasket where it mates to the heads Again.
The first time I had a set of cheaper intake manifold gasket so last time I forked out the cash and purchased a set of Felpro gasket set...
I just Ordered a New 3 core alumiunum radiator just woulding what is the coolant I should be useing with it.
I did some reading on this subject and just about everything I read dont tell you much they go in circles.
I just had to tear down my old 355 with 3000 miles on it and I did notice my...
The motor runs great but the Idel has always done this even when the car was stock.
When comming to a stop or getting off the gas to Idel hangs about 1000 to 1200 RPM's for a minute or 2 before drops down to the set idel of 750 RPM is this normal.
I set the base idel when motor hot set the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.