Welcome to the Corvette Forums at the Corvette Action Center!

Search results

  1. jenkx

    Backfire through carb

    My 82 C3 with crossfire injection is popping through the carb. It runs smooth during idle and low acceleration, but under torque or high rpm the engine runs rough and shows a compression backfire with no flames through the carb. My thought... intake gasket, lifter, head gasket. Any...
  2. jenkx

    Control arms bushings

    Could anyone recommend a spring compression tool for changing my control arms bushings on my C3. Thank you Sent from my SM-T550 using Tapatalk
  3. jenkx

    Computer reset.

    I have made allot of good changes to my C3 engine in the last couple of weeks. Should I disconnect the battery to perhaps reset the on board computer/processor? Thank you Sent from my SM-T550 using Tapatalk
  4. jenkx

    Rear main seal

    Has anyone changed a rear main engine seal without removing the ENGINE? My concern is re installing the oil pump shafts correctly. Thank you Sent from my SM-T550 using Tapatalk
  5. jenkx

    No cruising with control

    Help. MY 82 c3 has never had an operating cruise control. The switch seems to work work via tester and the servo holds vacum. I did install a new transducer also. All hoses are going to the right areas. There is a small solenoid on the top of the transducer that someone mentioned that it is...
  6. jenkx

    The tops.

    Would anybody know how to remove the old black silicone material under the weather stripping on the t tops. I need to remove this to apply my new weather stripping. Thank you Sent from my SM-G928T using Tapatalk
  7. jenkx

    82 carb rebuild

    I just finished rebuilding my carbs on my crossfire. The vehicle starts and runs better but the rpm is holding around 1500. Even when the engine is up to temp. Any ideas please. Thank you Sent from my SM-G928T using Tapatalk
  8. jenkx

    Drivers power seat removal

    Would anybody know how to remove a powered drivers seat that does not work. I have removed the cushions and I can get to the front bolts that holds down the front of the track. I cannot get to the back bolts because the motor needs repair. Thanks Sent from my GT-N8013 using Tapatalk
  9. jenkx

    C3 differential

    Has anyone change their differential oil? Is there a drain plug? Sent from my SM-N915T using Tapatalk
  10. jenkx

    Engine timing or drive shaft/u joints

    While hitting a cruising speed above 40 mph, I'm experiencing a vibration in my vet. If I let up on the gas slightly the vibration goes away. Any thoughts please. Sent from my GT-N8013 using Tapatalk
  11. jenkx

    Tach in off position on a 82

    My tachometer needle parks itself around 1500 rpm when I shut down the engine. Returns to normal when engine is turned on. Is this something that I should be concerned about? Thank you Sent from my GT-N8013 using Tapatalk
  12. jenkx

    Winter Storage

    I'm looking for advice on how to prepare my 82 vet for winter storage. My big concern is rodents. Is there a solution for keeping them out of the wiring, interior., etc.. Thank you Sent from my GT-N8013 using Tapatalk
  13. jenkx

    C3 transducer vacuum

    Mounted right above my cruise control transducer on a separate bracket, I have a vacuum relay that has a 2 wire connector on it. The unit is hooked up to the intake manifold via vacuum hose. It looks like it should have a vacuum hose on the wire side also. Any clues please. Thanks <br />...
  14. jenkx

    C3 vacuum unit.

    Mounted right above my cruise control transducer on a separate bracket, I have a vacuum relay that has a 2 wire connector on it. The unit is hooked up to the intake manifold via vacuum hose. It looks like it should have a vacuum hose on the wire side also. Any clues please. Thanks Sent...
  15. jenkx

    1982 c3

    I'm looking for the vehicle speed sensor that connects to the back of the speedometer and the speedometer cable from the cruise control to the speedometer. Any ideas please? Thanks Sent from my SM-N915T using Tapatalk
  16. jenkx

    Obd 1

    Does anyone know of a good OBD 1 code reader for my 1982 C3? Sent from my SM-N915T using Tapatalk
  17. jenkx

    New from the Mitten

    Hi all. I just knocked off a notch my bucket list by buying my first vet. A 1982 in decent condition. I look forward to being part of your group. Sent from my SM-N915T using Tapatalk
Back
Top Bottom