Welcome to the Corvette Forums at the Corvette Action Center!

Question: what if you needed a motor

midyearroadster427

Well-known member
Joined
Jul 25, 2004
Messages
191
Location
Massachusetts
Corvette
1967 Red 427 Roadster, 2012 Grand Sport Coupe
So...I'm thinking about the future a bit here. If you had your choice...would you buy a gm crate motor...454 or 502 and why? Now for reference...you would be traveling with it..say an avg of 8500 miles a season. NO Garage Queen. I am also thinking about a rebuild of the 427..but with all the miles on it..I am sure I will hear...we need to bore it out a bit..which I do not want to do...soooooooooooooo who thinks what..which is better and why... thanks for your opinions....
 
"BAG AND TAG" your original motor and go with the crate.

That's my $ 0.02.
 
Rebuilding the original 427 is what I'd do but that depends on what your intended use is. I don't see what the problem is with a .030 over bore. It makes the cylinders round and true again and with the proper new parts should be worth another 100,000 miles or more.

As for decking, I believe that process is way oversold by machine shops. If you are blueprinting a racing engine that's one thing but if it's a street engine, most times it isn't necessary. With the deck surface clean lay a straight edge across the deck in several places. Shine a light on the back side and look for any light under the straight edge. If there is no light at any contact area then it's flat. Same can be done with the heads. What more could be accomplished by decking on a street engine?

Now if you intend to do any hard running or racing then you may be concerned about lunching your numbers matching block. In that case I'd bag and tag as was said above and install a crate motor. You can't beat a GM crate motor with warranty but you will have to deal with the drill and tap for the clutch cross shaft on some blocks.

Tom
 
"BAG AND TAG" your original motor and go with the crate.

That's my $ 0.02.
Yup, why risk a #'s matching block? I'd use a crate also and drive it. When it's time to sell, you can reinstall the #'s matching engine...
 
Rebuilding the original 427 is what I'd do but that depends on what your intended use is. I don't see what the problem is with a .030 over bore. It makes the cylinders round and true again and with the proper new parts should be worth another 100,000 miles or more.

As for decking, I believe that process is way oversold by machine shops. If you are blueprinting a racing engine that's one thing but if it's a street engine, most times it isn't necessary. With the deck surface clean lay a straight edge across the deck in several places. Shine a light on the back side and look for any light under the straight edge. If there is no light at any contact area then it's flat. Same can be done with the heads. What more could be accomplished by decking on a street engine?

Now if you intend to do any hard running or racing then you may be concerned about lunching your numbers matching block. In that case I'd bag and tag as was said above and install a crate motor. You can't beat a GM crate motor with warranty but you will have to deal with the drill and tap for the clutch cross shaft on some blocks.

Tom

I gotta agree with rebuilding your original motor. Even if you have a deck surface that is out .003 - .005 as long as you run a good composite gasket you won't have any sealing problems.

I don't know why you are against an overbore on the original block. The only way to properly rebuild it is to get fresh, true surfaces and that will require an overbore whether you do it or the next owner does it.

I would also recommend a retro roller camshaft setup from someone like Comp Cams. You can eliminate the worry of losing a lobe to insufficient lubrication as many have seemed to suffer.

From your description of usage I get the feeling you will be driving the car as a cruiser rather than a racer. Nothing wrong with that at all. A properly rebuilt motor will last at least as long as the factory motor did and possibly longer.

I just can't justify pulling an engine, bagging it up and having it take up space on the garage floor for years in order to possibly satisfy some date d!ck who might buy the car from you later in life.

Rich:beer
 
perhaps I should have mentioned the block was not orig.. as for boring then we get into pistons and such...which now will bring the costs up to probably the cost of a new crate job. so ...I think a question that I should have asked first is ..which is better the 454 or the 502...what are the pluses and minuses of each..thanks guys
 

Corvette Forums

Not a member of the Corvette Action Center?  Join now!  It's free!

Help support the Corvette Action Center!

Supporting Vendors

Dealers:

MacMulkin Chevrolet - The Second Largest Corvette Dealer in the Country!

Advertise with the Corvette Action Center!

Double Your Chances!

Our Partners

Back
Top Bottom