Search results

ACS-7000 Here's the website: http://www.aclifts.com/parking/default.asp

As requested, here are some more details: This is the control unit which has the motor, pump and hydraulic oil reservoir (uses 3 Gallons): The button just under the warning label is the "Up" control. It turns on the motor, pumping oil into the piston, which in turn pulls the cables, raising...

I'll try to get some more photos this weekend.

The ceiling is 11ft, and in the pic, the car is up on the second from the top lock. It will go one lock higher and the car still fits, so I would guess about 10'6".

Freestanding.... Got the caster kit also so I can move it around as necessary.

New lift is here!!! If you are a DIYer and want to assemble a lift by yourself, here's some extra tools you will need: A real help to get it off the truck and move it around. It weighs 1450 lbs. (The truck driver was really relieved to see it.) And one of these: (That particular runway is...

Maybe if he gets a lift, your car will magically get done before you return....:L

Barry, We'll be travelling down to Southeastern VA for the birth of my 3rd grandchild at the end of Feb, and down to Northern VA for the 4th grandchild in mid-April. Maybe we can stop by during one of those trips. We'll see as the time gets closer. My car needs a long run anyway..:)

All kidding aside, It's pretty busy up here this time of year...... As soon as the lift arrives, I have to put my car up and pull my own trans to replace a bad pilot bushing. :bang All that work to replace a $10 part.....;squint:

When I had my 62 about 35 years ago, I too was chokeless... During a little test run, without air cleaners, I had the carb backfire on a cold day..... Then the rest of the car burned to the ground. Now I always run a choke, wait till it's warmed up before going anywhere, and always have the...

Hey Barry.. Everything is good up here. Everyone is doing fine. The trans job isn't too bad, the hardest part is lowering the rear of the engine down the right amount, then turning the trans just the right way so it will come out. My first time took a bit of finagling, the second time it was...

Due to the holidays, I don't expect to see it until early January. Normally ships about 2-3 weeks after order. They build them (pull individual parts from inventory, put all the parts in the boxes, etc...) after the order is placed. Then the cross-country shipping. Photos will be provided.

Had mine out today for a short ride around the block. First time it's been out of the Garage since April. Still runs.

When you click on the link, Get rid of all the crap before the "http://" in your title bar at the top of the screen, then it will work.

Pilot bushing replacement is the same job as a clutch replacement. First you have to get the transmission out, which is a job in itself. Then remove the bellhousing & clutch assembly. Finally, remove and replace the pilot bushing. While you are in there, if you need a clutch or throwout...

Thanks to the Holiday generousity of my wife, my ACS-7000 was ordered a couple of days ago. Yeah, I know, I haven't been on here too much lately.... New job takes a lot of my time (120 mile drive round trip every day) and no internet access at work. Still working on the house remodel too...

Thanks Steve. There are 2 coolant sensors. I've got the correct one feeding the ECM. New temp sensor and MAP sensor on the way. I'll keep you posted.

All the basics have been covered. Engine temps are normal, no overheating of anything like that. Have good exhaust flow. New plugs, correct timing, etc.... No codes are at the ecm except the correct code 12 indicating the ecm is working. If I disconnect any of the sensors, the ecm sets...

OK, Here's the update.... Rebuilt the TBI and Fuel pressure regulator.... no change. Replaced both fuel injectors..... no change. Pulled the intake manifold, replaced the gaskets..... no change. While the engine was running, I individually disconnected each of the sensors. After each...

I have a 91 Isuzu Trooper, 2.8 TBI, 4X4, 5spd. Two problems: It will turn over and start but stalls in about 1 second. It takes about 10 tries to get the truck to start. I have to keep my foot to the floor or it won't start. Once it starts, I still have to keep my foot to the floor as it...