Search results

I have my old R12 Manifold. Check with your friends, I would bet someone has one.

Hey RickC4, My comments were were done in August 2016 and for a C3. I am not even sure that the Link provided even exists.

First make sure the fuse is out. You need to take the driver side panel on the side of the console off. Then hold the bottom side of the cigar lighter so it does not spin. Good luck.

There is another method. See what happens when you get to sleep on something? There is a code that is stamped into the differential case. Its located in between the leaf spring plate that is bolted to the diff. and the torque strut bracket. Its a space about 3/4" to 1" wide. You will most...

To answer your question. It can be done, but you need to match the year of the car, engine size, transmission and reared. Then match the RPM and speed. So it is not easy. douglasamariani has the easiest way to figure out the rear end gear ratio.

Just a little clarification. Jack the car up so both wheels will turn. Posi: Jack both wheels off the ground. Turn one wheel 1 complete turn. - Count the turns on the drive shaft. Non-posi: Jack one wheel off the ground. Turn the wheel 2 complete turns. - Count the turns on the drive shaft...

I found this. I hope this helps. Removing dents from plastic bumpers | Search Autoparts Removing dents from plastic bumpers | Search Autoparts

I would pull the delay and see if that is causing the problem?

My question is did they paint the car with the bumper in that condition? If they did the the paint might crack trying to get it back to straight. if the car was painted with the bumper in that condition taking the bumper off will or trying to loosen it from the body might crack the paint. If you...

I don't know if it is the photo or the bumper. But, the bumper looks like it is pulled out from the bottom center causing the wave. The bottom edge of the bumper should be straight across from left edge to right edge. Yours looks curved. If it is curved it you might be able to get it back...

OK you peaked my interest. How do the Feds catch you?

This might be interesting on the subject 12 bolt conversion. Pertains to a Camaro! How to install Positraction and give your muscle car tire-frying capability

Do this google search there are plenty of answers out there. location of the power window circuit breaker on a 1974 corvette

I am not sure if I have the answer, but I have some good questions. Are you using the Car's Wifi? Are you using Apple Play? If you are to one or both, try disconnecting your phones Wifi. I have a problem in my car that the phone and the cars Wifi seem to conflict with each other and causes...

Thanks again Tom. I have learned that it is not in the AIM because the knuckle wheel hub assembly was delivered to the factory as a assembly.

if you do that I would really appreciate it. Thank You.

I am redoing my front brakes and went to my trusty AIM and can not find a detailed diagram for 1977 corvette steering knuckle wheel hub assembly diagram. I was looking for the caliper bracket dust shield and associated hardware. Am I missing something?

It is not impossible. It all depends on what you want to spend. You need to find a rear deck lid similar to the one in the link below or get a rear clip from a 1974 - 1977 Corvette. I had a problem finding a deck lid for a 1974-1977 for a T-top car.C3 Corvette 1968-1973 ACI Fiberglass Rear...

Attached is a Willcox headlight diagram for a 69 Corvette. Since your 69 has only one relay (later models have 2 relays) that does not seem to be the problem. I would trace each hose back to the source with a vacuum gage to make sure there are no leaks. It sounds like there is a leak on the...

Yes , you need two bleed hoses connected to each bleed nipple on the caliber halves. With someone on the brake pedal , open each bleed nipple in turn, close off with the pedal on the floor. repeat until all the air is out and them move across to the other rear wheel . do the same before moving...