Search results
-
Newbie here
Welcome to CAC Enjoy Sent from my moto z3 using Tapatalk- bill81vette
- Post #3
- Forum: New Member Introductions
-
C3 VIN/GM Invoice Mismatch
If you don't have the vin,how can you find your old vette?? Sent from my moto z3 using Tapatalk- bill81vette
- Post #3
- Forum: C3 General Discussion
-
C3 VIN/GM Invoice Mismatch
Do you happen to have a copy of the build sheet?? Do you know if it was built in Bowling Green or at Louis??? IF your vin/allied sheet shows a B5 Prior to the last 6(?) Of the vin,you can call the museum to get a copy of the build sheet. If it's a St Louis car you be out of luck.(BS)is the 2...- bill81vette
- Post #2
- Forum: C3 General Discussion
-
-
Loose wiring
1st, Welcome to CAC!!! The top photo is a ground strap`,usually goes to the frame and/or engine,tranny,or something metal to help ground the components. the bottom pic looks like a ground and a power(flat with the hole is the ground).look around that area to see if the plug fits some thing that...- bill81vette
- Post #2
- Forum: L81 Vette Registry Forum
-
Here at Corvettes at Carlisle
I am,but you knew that Sent from my moto z3 using Tapatalk- bill81vette
- Post #3
- Forum: News and Announcements Forum
-
New Member from Metro Detroit
Welcome to CAC Enjoy!!?? Sent from my moto z3 using Tapatalk- bill81vette
- Post #4
- Forum: New Member Introductions
-
1981 Idle Adjust?
Welcome to CAC!!!! enjoy!!! have you tried to drive this vette or just started it and run the engine??? it may just have to be run,but yes it may have to be rebuilt.- bill81vette
- Post #2
- Forum: C3 Technical and Performance
-
-
Help! Odometer not working
I didn't read it correctly... your right. I just fixed mine last year Sent from my moto z3 using Tapatalk- bill81vette
- Post #5
- Forum: C3 Technical and Performance
-
Help! Odometer not working
Welcome to CAC!!! Enjoy!!! Either your speedo cable has broken or the gear in the transmission has been stripped. Do you have a factory service manual??? Sent from my moto z3 using Tapatalk- bill81vette
- Post #3
- Forum: C3 Technical and Performance
-
Help! Need 24 Pin White Connector to ECM 1225550 on '82 Cross Fire
You might want to try lectric limited They have a lot of harnesses for the older vetted. You may to buy a harnesses to get it though... FYI Good luck Sent from my moto z3 using Tapatalk- bill81vette
- Post #2
- Forum: C3 Parts For Sale / Wanted
-
Choke light
Start checking your ground's. Make sure they are clean and free from dirt/rust or corrosion. You can usually find them along the frame. Sent from my moto z3 using Tapatalk- bill81vette
- Post #6
- Forum: C3 General Discussion
-
Hi, new to Corvettes and need help with LT designation
Welcome to CAC!!!! Enjoy!!! Sent from my moto z3 using Tapatalk- bill81vette
- Post #5
- Forum: New Member Introductions
-
Hello, New member from Massachusetts. I'm 66 and looking to buy a used Corvette within the year
Welcome to CAC!!! Enjoy!!! Sent from my moto z3 using Tapatalk- bill81vette
- Post #6
- Forum: New Member Introductions
-
Choke light
If your choke light is on, the wire for it should be plugged into the RT side of the carb. Sent from my moto z3 using Tapatalk- bill81vette
- Post #3
- Forum: C3 General Discussion
-
Choke light
The gauge switch is the pressure switch. Sent from my moto z3 using Tapatalk- bill81vette
- Post #2
- Forum: C3 General Discussion
-
New member
Welcome to CAC!! Enjoy! Sent from my moto z3 using Tapatalk- bill81vette
- Post #3
- Forum: New Member Introductions
-
-
Howdy!
Welcome to CAC!!!! Enjoy! Sent from my moto z3 using Tapatalk- bill81vette
- Post #5
- Forum: New Member Introductions