Search results

Greetings All, 1988 vette coup...BOSE speakers/amps. I need to know if anyone has a link to or, knows the ratings of all the electrolytic capacitors on the boards of the front door amps. I replaced the two larger caps on the board to narrow down some issues and, need to purchase all the rest...

Greetings All, Looking for the front door speakers for a 1988 C-4 vette....I don't care about the amp(s) or cases. Also seek info for a good "drop-in" replacement if known. Thanks for any assistance!

Greetings, ......Been a while since I've been back here.......Looking for the AUX COOLING FAN for a 1988 vette as it's bearings are "going south".... Some other years may be interchangeable....This is the fan at the extreme front of the car in front of the a/c condenser...thanks.

greetings, are there any "kits" sold to rebuild my 1988 master cylinder (dual resovoir). is it difficult? any tricks to it?.........thanks!

greetings, since i bought my car, i have noticed that it takes a few "spins" of the starter before it starts. forget the injectors, timing, wires, plugs, fuel pressure, filter and pump, etc.,. the specific question is; the oil pressure switch when reaching approx 4lbs of pressure while...

greetings, would anyone know if a bose radio from a 2000 vette is directly interchangeable with a 1988 vette?....thanks!

greetings all, strange question here. i need to locate some belt dressing-grip that comes in a solid stick form. anyone know of a place that actually sells it. i know that there are sprays but, don't want 'em and i know that the sprays have taken the place of the solids over the years. the...

BELOW IS THE RESPONSE I HAD FROM DEPT. OF TRANS., U.S. .THOUGH, THIS IS NOT THE QUESTION I HAVE ASKED, IT IS INFORMATIVE NONETHELESS. I MYSELF HAVE REQUESTED REDRESS TO MY SPECIFIC SITUATION. @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Q; Are There Any Limitations on My Right to Have My Vehicle...

How To Drop Hush Panel, 88, Pass. Side to access Comp. greetings, acquired a computer with hypertech chip. i am having great difficulty in accessing the computer under the passenger side hush panel. what is the process or where are the screws? i have removed some by the floor light as well...

greetings, a forum menber has offered to assist me, (hell, he is gonna do all of it, i have to give credit where credit is due!) to get a "chip?" for my stock 1988 corvette ecm computer. herein lies the problem. i am not sure what that is (memcal) so, where can i buy them and what is...

greetings, when replacing the ecm on an 88 vette, do i simply release the two clips on the sides of the prom and simply transfer it to the new computer? 2nd, is there any forum member that could burn me two (2) proms, completely stock, for my car? if so, what info do ya need? can a scanner...

damn these 88's!....could a misadjusted or bad IAC MOTOR cause a car to stall - stop running while actually in motion or does it just come into play while car is at idle at light or while in park. i keep having this re-occurring problem with my car dying momentarily while driving it...

i just ran across an air cleaner housing that has a k+n air filter in it as well as the box being "cut". whomever did this did an excellent job as it looks factory. how do i clean the air filter element as it is rather oily? when clean, what color should the filter be? there has to be more than...

greetings, strange problem here. while driving even at a high rate of speed, i am getting an intermittent problem with my car cutting out (shutting down). it is only a momentary cut off at this time. .......88 vette, 74k miles. new plugs, cap, rotor, ignition module (under cap), ignition...

greetings, i procrastinated too long and i had to be flat bedded home yesterday as my bearing crapped out on me. however, i had all the parts (bearing assemblies, 4 u-joints) sitting on the bench at home. today, i attempted to replace and change out everything and broke 1 of the 3 torx 55 bolts...

greetings, i procrastinated too long and i had to be flat bedded home yesterday as my bearing crapped out on me. however, i had all the parts (bearing assemblies, 4 u-joints) sitting on the bench at home. today, i attempted to replace and change out everything and broke 1 of the 3 torx 55...

greetings all, well, as i suspected...rain. oh well however, this gives me another chance to ask another question about rear bearing / hub assembly in my 88. i have looked at he helms manual and it is not all that clear. so, i will asked here to those whom have done this already. 1. i raise...

Greetings All, Like it says, will the air box for an 85 vette fit into and is compatible with an 88?....thanks!

greetings, here is a stupid question and a most embarrasing one. i am going to do both rear bearings and u-joints on my 88 as i have been hearing a couple of "clicks" on the passenger side last week. i have realy only dealt with "standard" fasteners but, not torx of any sort. i would rather...

greetings, I have a question if I may ask. I have an 88 vette and want to be sure my vats system doesn't crap out on me some time in the future. in the past day or so, I have be not able to start the vehicle due to the vats system as so my code reader and scanner have told me. i either waited...