Search results

1986 heater core - CorvetteForum - Chevrolet Corvette Forum Discussion Is changing the heater core on a C4 really that bad? - Forums - Official C4 Vette Registry - C4 Corvette Registry Heater Core Heater Core Removal and Replacement - 1989 [Forums - C4 Technical] - CorvetteForum.guru

This might help. Replacing or Repairing the Shifter Cable on a C5 Corvette with an Automatic Transmission Roy

Belt have grooves on both sides ? The original pulley is grooved , new pulley should be grooved . If I still had my 92 I would look at it to be sure.

dealing with a stuck C4 hood | Grumpys Performance Garage

.The 92 had 131000 but better interior and paint . The 87 has 55000 , clear coat starting to show its age and the interior is good but is faded from too much sun .I liked the ride , more like my 62 that I had for 36 years. Both cars are rust free , the L98 was the main reason I chose to...

I sold my 1992 last week , I will keep the 1987 . When I bought the 95 in 2006 I never intended on keeping it this long but my wife liked it. We put less than 100 miles in the last 2 years , so when she said might as well sell it , took less than a week. Her only request that I get the AC to...

Found this and know how it should be wired , just need to know what batteries needed, 20170305_112103.jpg 4801K View Scan and download Roy

I have a Snap-ON MT-406 that I am trying to repair for a friend. I need to know what batteries are required . I think that 2 of batteries are 9V and I am not sure if they were wired in series or parallel .Snap-On sent me a manual but responded that the did not have any information...

I just looked at my 92 again tonight and looked at the picture and the AC clutch is plugged in. I do not know where the unhooked plug goes .

This might help. http://www.corvetteactioncenter.com/forums/c4-general-discussion/120665-question-how-open-rear-hatch.html

Turbo Iroc - engine swap part 3 - removal of the TPI plenum, runners and fuel rail - YouTube Two bolts ? one each side that are on the back and reached from the other side. Keep track of the runner bolts , what I recall from 2005 when I changed head gaskets that all the bolts are not the...

How to change the heater core in a 1990-1996 C4 Corvette. - YouTube file:///C:/Users/Roy/Downloads/Is changing the heater core on a C4 really that bad - Forums - Official C4 Vette Registry - Corvette C4 Registr This is what I found on line and they did help but I would follow the FSM and...

I did this without removing the dash pad. If I had to do it again I would follow my FSM . At 71 I did not keep track of how long it took me , if I had it would be in days not hours. No leaks and only had one screw that I did not replace in the defroster duct flange.

C1 Removing the body from the frame on a 62 plans for corvette body cart - Google Search body lift - 1957 Corvette - YouTube Roy

Towed my 92 on a tow dolly to get it home . I had a problem with the wheel straps were a little small as I have a older tow dolly. I disconnected the rear U-Joint and zip tied the drive shaft to hold it , my 92 has auto trans. Lock the steering wheel or it will not track behind the tow dolly...

A machinist that I know removed 2 mount bolts that I broke off in a Tracker aluminum front differential . He used a tig welder starting in the center of the bolt and building a ball of weld to turn with vice grips . One bolt did not want to turn so he added more heat by making the ball bigger...

Have you looked at the CrossFire Injection Mine ? Scroll down to the Corvette General Form and check it out .

On my 87 I found that the EVAP line had a short piece of rubber line where the frame kicks up on the drivers side. I found the leak by taking off the EVAP line at the canister and the fuel pump,plugged one end and a little air pressure in the other end.

zzzzz

zzzzz