Search results

Did find them. On under the washer tank passenger side and one under battery tray driver side in case someone are looking for them. Have a yellow lead cover going to the sensors so easy to find them when you know where thay are. They looked like new and no rust at all so investegation is...

Location of sensors Hi again. I cant find those sensors:mad Anyone have a picture to post or some pin point location for me? Steve

Have light in the inflatable restraint and red a bit on this in the FSM. Aparently it is a gommon problem that the grounding at one ore bothe sensors in the fraont fails. Anyone done this job before and can give me a short story in how to fix this. I am a bit worried as i dont want the bag to...

Update Went through the FSM and as the ASR was ok i had to ponder a bit. Disconnected the el plug at the reservoir and all lights went off, topped the reservoir with brake fluid all the way up to where the treads start and problem solved. Aparently the reservoir they used on the 1993 have a...

Hi. Have the check ABS and the red brake light on in my 1993 Corvette. Connected the tech 1 and had ABS code 62 and 83 coming up, deleted them and as soon as i start the car the center consoll check ABS and the cluster brake light comes on. Also had two previous codes (041H and 072H) which i...

Brakes done 500 miles ago They are drilled and slotted Noise before replacing Did not come with grease :-(

I checked the bearing with lifting up the car and it is as thight as it can be. I check the sensor tomorrow but the strange thing is that when i put my foot to the brake pedal slightly it stops.

Have a clicking noise when driving my 1993. When puting my foot slightly on the brake pedal it goes away:eyerole It all looks to be ok, have new discs fitted and new pads. Sounds to be frome the drivers side forward but hard to tell. Any ideas? Regards, Steve

Thank you guys. I used a 24 mm socket and hammered it in. Then it came out easy as that. This was the final one as i did all tires and the tool lasted for thre and caused my problem. As a nice to know i want to add that the pin securing the front brakes can be replaced with a bolt and a locing...

Hi. Have the original safety lug nuts and the tool is busted. Have only one more bolt and cant get it off. Any ideas how to get the tire off the car as i am change to new wheels. Thanks, Steve

Worst case is your sylinder head gasket are blown. Remove your oil filling cap and check if there are any white colored grease on it and your cooling water for oil. Both means gasket. Whith a rich smell it might be from the colant fluid and i am quite sure it is a blown gasket :-((

Stil the same. Motor is working as i can change temperature. The issue is that it want be as warm as it used to be before i was fiddeling by it. Thank you for your addvice. Steve

Hi. Is there a anywhere i can order new replacement door stickers for a GM car in USA? This is not for my corvette but my Tahoe. The sticker with VIN #, tire pressure and weights emty/loaded etc. Thanks,

Thanks. I keep on looking.

Hard to find, want one spare:) I have a spare computer, never been installed in a car in the garage just in case. Steve

Is there possible to buy a new original spec chip for a 1993? Thanks, Steve

Anyone know if there is a purpose made stand for C4 on the market. I have two stationary nokia phones and had the Tahoe in mind for one and the Corvette for the second. Thanks, Steve

Thanks vetteoz. How do i releave pressure in the fuel line before removing? Regards, Steve

Hi. Anyone have a link or some info regarding this job on a 1992/1993? Have 8 new injectors in the garage from FIC which i had there for a while. Now when it is winter seams to be a good time to do the job :) Thanks, Steve

I just replaced mine as the old original one where soaked during a heavy rainstorm this summer. Left the car in the garage for 4 weeks when being away for work and when i came home it started to idle very rough and then just died. No spark at all. Replace the whole thing when you first have to...