Search results

94 - Gasoline drips while I'm disconnecting/connecting the inlet hose on the new fuel filter, (ACDelco). The line comes from the gas tank, and is probably lower than the tank, directly connected, so the fluid drips from the any available hole, in this case the open inlet pipe. Is there a way...

Will an LS1 fit into a C4(94)? Will an LS1 take the C4's ZF6?

I've got Flowmasters on my 94. Love the sound. I agree with the "deep" rumble description and they do gurgle on decceleration. When I'm parking at work, I shift into second in the parking garage to drop the rpm and almost always setoff a car alarm or two. I'd swear that sometimes they...

Ambient minus 25 to 40 puts me right in the range, actually a 36 degree drop. I expect to see a smaller drop as temperatures increase. Thanks

Re-charged my 94, first year for R134A. Here are the numbers I got. :blue: Ambient temperature - 80 F Air Temperature at A/C vent - open doors - 40 F Low pressure - 26 to 27 psi High pressure - 190 to 195 psi Humidity - 49% - as reported for region via weather forecast. My method was to...

Re-charged my 94, R134A Here are the numbers, may be used for reference for your charging. Ambient temperature - 80 F Air Temperature at A/C vent - open doors - 40 F Low pressure - 27 psi High pressure - 195 psi Humidity - 49% - as reported for region via weather forecast.

Thanks, checking it out.

I've got a 94 so I already running on R-134a. Researching doing some a/c work. Can anyone recommend a vacuum pump and vendor for additional a/c tools?

At least on a C4 you won't have to set Dwell angles any more. Think you see a lot of pavement on a C3? You've never worked on a 78 Malibu. You could rent a studio apartment down there.

There are really two C4's. The 91-96 should have been called C4.5 - LT1. ZR-1 styling, the ZF6, ABS and traction control, big, big improvements. How can you knock sharing the same transmission with the ZR-1?

Also check for debris in front of the radiator - when I bought my 94, it looked like a bird's nest was plastered to the radiator.

I spoke to Moog technical support - the guy said the upper ball joints have be redesigned and the four bolts are sufficient. Thanks for the replies.

I'm replacing my original upper ball joint on the left side due to a torn boot. My mechanic also tells me the tire wear patterns point to the same ball joint, (and 95K miles). I'm replacing it with a Moog. The original ball joint lightly tapped out with a hammer quiet easily. What worries me...

My 94 is a 6spd, its a DD and I drive in traffic to work everyday. 80 mile round trip, with 20 miles of often bumper to bumper traffic. I'D NEVER DRIVEN A STICK BEFORE EXCEPT FOR A CROSS COUNTRY DRIVE IN A RENT-A-TRUCK FROM NY TO FLORIDA IN 1985. I love the stick and wouldn't have it any other...

When my headgasket blew, I had very,very thick white smoke out of the exhaust, and horrible overheating, bubbling, boiling radiator fluid. The car drove so terrible I didn't drive more than 10 mph home. When I finally pulled the head, I couldn't believe the gasket still looked 98% OK, just a...

The picture is small but the car does look nice. We almost have twins, note that mine is a 94 polo green. Thanks for detailed explanation.

Good idea with the masking tape and the recommendation to avoid edges/corners. Thanks, very good point.

Understood, thanks. I'm doing a lot of research and going to test the procedure on my 98 Windstar first. How's that for a set of priorities?

I'm going to pick up a Poter Cable 7424. Meguiar's recommends a yellow pad with M80 Speed Glaze followed by a tan foam finishing pad with NXT Tech Wax. Question 1. I'm sure Meguiar's sells a good pad. Any other recommendations? Question 2. If I understand what I've read, the Glaze/Wax is...

good point!