Hello All,
I have a 1975 350 manual shift. Bought a 1604 Edelbrok carb and installed with pressure gauge and pressure valve. Fuel pressure set to 5.5 to 6 pounds. The problem is the engine stalls on idle. If you close the choke down the engine idles fine, but if the choke is open the engine...
Hi All,
I have a 1975 350 4spd. I purchased and installed an Edelbrock 1406 600 cfm carb. When the car idles everything is fine including revving the engine. However when I put the car in gear and go down the street the engine sputters like it's going to stall. I need to take the car out of...
Hi All,
I had to replace the ignition switch actuator rack in a tilt telescopic 1975 steering column. Everything looks fine and works great with the column cover off. However when I install the column cover the key ignition cylinder is very tight to remove and insert the key the key will...
Hello All,
I have a 1975 Tilt Telescopic sterring column. Can I swap it for just a tilt steering column with no modifications or electric conversions?
Thanks
When I turn the ignition key the rod on top of the column that goes to the ignition switch does not move and the engine will not crank.
I removed the steering column. How do you repair or replace this. Does anyone know or have pics or video on how to do this?
Thanks
Hi All,
I just finished tuning up the car and all is project, engine runs beautifully. 30min later I turn the key and the engine will not crank at all. I thought it was that feature that the clutch had to be depressed for the engine to crank. Is there a way to disable this so I rule it out as...
OK just saw that when the secondary flaps open they do not close back all the way because the Rod Sec Meters do not seat back down all the way. You have to play with it for it go all the way down and the secondary flags close all the way.
Will this cause the hesitation when the pedal is floored...
Can anyone please help. Had a 1975 Quadrajet carb rebuilt for 1975 350 manual Corvette. The car starts idles and drives great. But if you nail the gas pedal the car hesitates and no pickup or power. If you cruse all is well and pick is perfect, problem is just when you floor the pedal is when...
Does anyone know how to remove and install the ignition lock cylinder on a 1975 tilt wheel. I was told that you stick a rod in a hole by the ignition cylinder lock and turn the key backwards to remove it. Is that true? Thanks
Hi All,
I'm removing the upper control arms but can't find any store that has the attachment to a slide hammer to remove the upper control arm bolts. Can the bolts be removed another way? Can you use a hammer or any other tool?
Thanks.
Question: I will be doing the rebuid of both front and rear suspension with the body on the car. Is it more difficult? should I pay and have it done or can you do it with the body on without any issues. All I have are the tools and floor jacks. Thank you for all of your posts - GOLD info!!!!!!
Hello All,
I have a 1975 convertable and want to rebuild the front and rear suspension. I have never done any suspension work but want to try to rebuild id myself. Can anyone recommend good paper, books or video's on how to do it step by step?
Thanks
The 1975 Assembly Manual does not show where it goes, only a general picture of the unit under the dash but not it's correct loaction. Can anyone take a picture of theres and post it?
Hello Everyone,
I have a 1975 convertable. The drivers side courtesy light was missing from day one. I finally go a courtesy light frame support and wire bu have no clue where it mounts. The both service manuals do no show where it mounts. Does anyone know where i mounts on a 1975 C3 and have...
I just installed a new Dewitt’s radiator and had to remove the top two radiator support screws and loosen the lower screw (kept the stock clutch fan). After the install any time you put the key in the ignition the headlights are on. If you take the key out the lights go off. Just replaced the...
Hi, I'm having a strange problem. I have a 1975 convertible and removed my dash console gauges about 3 months ago to restore and replace some gauges. Replaced the Fuel gauge, clock and replaced all the light bulbs. When I put the dash in the car (not bolted down yet) plug all gauges and lights...
Can anyone help. Need to remove exterior windshield molding on 1975 convertable. I manage to get the side molding off but top and bottom need help. Does anyone have a video or pics on the steps to remove the top and bottom exterior molding? Anything whould help greatly.
Thanks.
Do I really need to drop the tank, or can I remove/install the sending unit without dropping the tank? The problem I'm having is the fuel guage keeps bouncing when driving. If I'm at a stop the guage is fine. Was told that the sending unit is the fault but now not so sure?
Does anyone know if the fuel sending unit on a 1975 Corvette is located on the top or bottom of the fuel tank? Do you need to drop the fuel tank or can you remove without dropping the tank? Thanks.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.