I delete items from this list as they are sold. Everything listed is available.
Used small block heat riser valve works fine. $19
http://home.mchsi.com/~magicv8/adpics/riser.JPG
used 63-79 driveshaft $59
http://home.mchsi.com/~magicv8/adpics/driveshaft.JPG
One set of NOS AC 44S spark plugs...
My 66 got 19 to 20.5 mpg on the highway with 3.08 differential gears, and still
had enough torque to just let the clutch out at idle in first gear without
stalling. I had this diff rebuilt about 8 years ago for a spare, sealed it in a
bag, and boxed it up.
The rebuilder replaced clutches...
My 66 got 19 to 20.5 mpg on the highway with 3.08 differential gears, and still
had enough torque to just let the clutch out at idle in first gear without
stalling. I had this diff rebuilt about 8 years ago for a spare, sealed it in a
bag, and boxed it up.
The rebuilder replaced clutches...
Rebuilt Muncie 4 speed removed from a 67 GTO with 2.5 to 1 first gear, RH speedo location. The rebuilder replaced synchros, seals, and any other parts that looked worn. I crated it up in 1995 as a spare after testing it in my car for a week while my other Muncie was being rebuilt.
Pick up in...
FS: rebuilt 3.08 differential fits 63-79
I had this diff rebuilt about 8 years ago for a spare, sealed it in a bag, and boxed it up.
I'm selling my Car soon and won't need the spare.
The rebuilder replaced clutches, seals, and any other parts that looked worn.
cast date a223, stamped LRW037E2...
I had this diff rebuilt about 8 years ago for a spare, sealed it in a bag, and boxed it up.
I'm selling my Car soon and won't need the spare.
The rebuilder replaced clutches, seals, and any other parts that looked worn.
cast date a223, stamped LRW037E2 and has GM gears
Pick up in Moline IL for...
Rebuilt Muncie 4 speed removed from a 67 GTO with 2.5 to 1 first gear, RH speedo location. The rebuilder replaced synchros, seals, and any other parts that looked worn. I crated it up in 1995 as a spare after testing it in my car for a week while my other Muncie was being rebuilt.
Pick up in...
The tour begins in two months, and I am wondering if anyone else on this forum is planning to join.
2009 HOT ROD POWER TOUR(TM) ROUTE
Saturday, June 6 Madison, WI
Alliant Energy Center
Sunday, June 7 Racine, WI
Downtown Lakefront
Monday, June 8 South Bend, IN
St. Joseph County Fairgrounds...
In the Pit Stop column, on pages 132 and 134 it describes the older "ammeter" wiring with "external shunt" that c2 owners have had to come to terms with.
7 cities in 7 states in seven days, a 2600 mile loop.
Little Rock start with half the cars out of the gate
I loved the Duke
...also northern tin
Springfield MO
on the road again
Jay Leno's $250k Pratt and Miller car
ya know yer in Kansas when..........
You're in IA when the...
I stopped at the shop that painted my car and Mike was painting a 69 Camaro air dam, so I got a chance to compare it to the air dam on my 66. First I put the Camaro air dam in the mold made from my air dam, then I put the Camaro dam next to a dam made from the mold. The camaro dam has a deeperV...
I'll post even more of the tour pics later. Editing the pics for web use takes a lot of time.
The pics are here: http://www.corvetteforum.net/classic...e/index7.shtml
Not as elegant as 67heaven's hood, but it will do.
A few years ago, when I noticed the stinger on the underside of the hood let the fan recycle hot air over the top of the A-C hood seal, I stuffed a piece of foam in the stinger above the hood support to fill the gap. That not only helped city...
I can't find the torques for the bolts that hold the front brake shield and the caliper bracket to the steering knuckle. My 66 aim and service manual are no help. Does the 65 or 67 aim or manual show the torques??
Answer:
I forgot to put back the rubber caps I made for the coil primary studs. Had to run to NAPA for more pink wire. The line now has a fuse in it too.
I got my cellalarm in the mail this week and hooked it up to my car alarm. It works great. If my car alarm goes off, the cellalarm calls the phone I carry. One more level of protection, and a good one too.
Could someone please tell me the distance from the center of the spindle (hole) to the center of the frame anchor bolt (hole)?
I am checking a rear wheel alignment at home, and I need to know how much tire movement (toe in) occurs when shims are moved at the anchor bolt.
Could someone please tell me the distance from the center of the spindle (hole) to the center of the frame anchor bolt (hole)?
I am checking a rear wheel alignment at home, and I need to know how much tire movement (toe in) occurs when shims are moved at the anchor bolt.
The temps had been unstable and surging coming off expressways. I have a Griffin BB radiator and a 16 inch Derale fan in the stock shroud opening - with Derale temp control. I've been trying mods to get the thing stablized. Some hot days it works perfect, some cooler days unstable - then hotter...
is working on one.
I was under the Corvette, trying to dislodge the differential pinion nut - when my neighbor went out to his garage, pulled the cover off his red Miata, got in with his wife, and drove off with the top down and the stereo blasting. I thought to myself, I wouldn't trade...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.