The Rep was right on the bearings, they are not as 'beatable/durrable' as one would think. I replaced an output shaft/ drive pulley bearing on a Buell motorcycle, and special tools were needed. You could only push it into the housing by pushing the outside diameter of the bearing, if you touches...
On the 82 the door has a pin with a torx recess and is located on the pillar opening adjacent the side of the seat on the door sill It is adjustable to facilitate door gap on the rear of the door, to align the body and door seam. If I loosen this stud/pin will it spin on the interior of the body...
I'm sure I'm not the first as I'v looked all over the web trying to locate an EGR solenoid for my 82 C3. I can find nothing.... yikes...:ugh. Going to the Crossfire Forum also was ineffective as no search provided any information. It has been spoken of that a similar year 'purge' solenoid was...
This is from the "Corvette forum" so all credit goes to the author. I'm simply copying it and pasting.
03-29-2010, 07:35 PM
#2
RaymondD
CF Member
Garage is...
I'v got plans for RHS heads as well, but on a SBChrysler motor. After scouring all the forums about heads and build-ups with RHS heads, I was a bit alarmed by some discussion with the early RHS heads and peculiarities that rose-up with casting and ports and valve spring seats. I hope you got...
What you have is a savings account that can't be easily accessed. One thing I would do though is either NOT drive it OR REPLACE those ORIGINAL tires........... they are a bomb just waiting to destroy your bodywork in the event they let loose................. I think you'v probably thought of...
My rear passenger side is that way. It appears the PO used some contact cement or Gorilla glue..... sparingly, and got it to stay. I havn't had any problem with it becoming loose and there's no extra gooped out around the circumfrence, just the inside pinch area.
Mine does the same thing, in a couple minutes time it flops down right in the line of sight, Dangerous and Annoying. It seems the hex rod that the flap is on stays in position, rather it doesn't rotate, just the sun visor doesn't have enough pinch and it will rotate and flop down. It seems the...
Can someone tell me what this piece is. It is plastic in the center of the photo with two rubber hoses. One to the rear as can be seen and the other going to the base plate of the crossfire venturi on the passenger side of the manifold. Currently if I hook it back up to the manifold, it kills...
Mine is an 82 C3, and I'm sure some of you have seen or had or heard of hogged out tumbler lock holes in the door. By hogged out, I mean the positioning lug on the tumbler having carved slightly into the door skin. Thus when you manually open the door unlocking it with a key, you will...
AND...... I believe this is what the circuit is on my 82, and locations of what makes the fuel pump run..... What a pain, it may be simple, but an akward fix just the same, wish me luck getting it going.....:ugh
I have bought a fuel pump relay, yet to be installed, and according to the PO the fuel pump is new. I will check the fuse first, (a bich to get to for me) and trace on down the line to get power to the pump again All this I'll try to fix today. What I'm having trouble identifying is this...
This hesitation
I have something of the same problem on an 82. If I floor it, it bogs, rather it seems it looses fuel, recovers, or maybe bogs again and then accelerates like regular. I don't know if this is something or not, but as this happens (full throttle acceleration) it almost seems the...
I think this is the link you speak of.....
http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0CD4QFjAA&url=http%3A%2F%2Fwww.splashedpaint.com%2Fcameron%2FCruiseControl%2FCruiseControl.pdf&ei=hj54T4LnMsyItwe9ocmPDw&usg=AFQjCNHUfzjVW64DpyGwnxMODtqe7RnOZw
Ok, coming back to the clearance problem. In my readings about changing from Xfire to carb, I did read that a Performer would fit, however an 'Air Gap' would not (Too high) and that depending on the carburetor heigth and what aircleaner. The aircleaner needed to be a drop down style and the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.