What have you done to make your vette perform better?

[nelson84]

When I changed the plugs, cap & rotor, installed hypertech chip & 160 stat, and straight pipe. It runs so much better. Fairly basic stuff but runs super cool now and a little more snap when you hit the go pedal.

Any other good mods that are easy to do?

my others are:
shift kit
K&N
IAT relocated
fuel pressure regulator

future mods:
cut out MAF screens
cut air lid
pulleys
air pump eliminator kit

future futer mods:
new engine with superram & vortec heads with lingenfelter cam

 

[WNH]

I ported the plenum.
I took the plenum off and widened the holes that send air thru to the runners.

 

[rrubel]

I elected to take a more... radical... approach to more performance:

http://www.facebook.com/album.php?aid=16634&l=c9af6&id=809077305

[RICHR]

 

[WhalePirot]

That Super Ram is a real picnic, isn't it? I am faced with taking it off, again, in my re-do of some 'professional' work. As long as it is apart, I will epoxy paint or powder coat it, as that aluminum needs help, IMHO. Polishing the ribs on top if very time consuming and dirty work.

Yeah, I went a bit radical, too, but the odor of liquefied rubber grows on ya.

 

[rrubel]

Not sure which smells better, the odor of rubber or victory over new mustangs... but I'm hoping to not have to take off the SR for a good long time. There's a cool-looking intake by FIRST (http://www.firstfuelinjection.com/products.htm) which I may get if I do have to remove/replace anything major. It's a TPI, but much much better than the stock ones and it looks easier to work on/around.

I just realized I still have your old radiator in my garage, Whalepirot...

[RICHR]

 

[*89x2*]

full and proper tune up

 

[Black Bart]

89 Corvette coupe 6spd\ FX-3 suspension \ Chrome GS Wheels 315\35\17 G-ForceKD's \ SB-406cid\ Procharger D1-R \ Custom built 8 Rib pulleys\ Custom built Spearco intercooler \ Spal Fans \ NOS wet nitrous system controlled by jacobs mastermind controller \ Spearco water/alcohol injection system \ TPIS Mini Ram II \ 58mmTB \ AFR heads \ AFR rev kit \ Manley4340 push rods \
Comp cams custom grind roller \ Comp cam lifters \ Comp cams roller rockers 1.6 ratio \ Ross custom pistons 4340 pins \Speed pro rings \ 6 inch eagle 4340 3d rods \ eagle 4340 crank \ fluid balancer\ Engine electronically balanced \ Cloyes true roller timing chain \ Melling high output oil pump \ 10 qt. multi trap door pan \ large oil cooler \ MSD-Digital-7 ignition\With MSD pro-power coil \ MSD boost retard \ Msd super conductor wires \ Accel DFI Gen.7 W/wide band \ 83lbs injectors \ Centerforce clutch & flywheel \ TPIS jet hot coated headers
\ 3” dual exhaust with electric cut outs \ 13 inch rotors C5 calipers w hawk pads \ Air dam with air ducts to brakes \ Triple pillar pod with Autometer gauges \ Air-Fuel \Boost \Fuel Pressure \ lowering kit \Escort radar detector \RM radar jammer.
The difference between men and boy’s is the speed of their toy’s.
IF IT’S NOT BLOWN THEN IT SUCKS

[/IMG]

 

[MR NICE]

LT1 intake,cam,heads,rr,headers,and all the stupid stuff.

 

[road agent]

I don't muck with it!

 

[KANE]

No- I don't have this one myself... but it will be interesting when BBK finally gets it into production...