Welcome to the Corvette Forums at the Corvette Action Center!

Recent content by Dave65

  1. Dave65

    Coil Springs what would you do?

    Mark, The specs I got from Chevrolet in the information packet they sent me are Part number ---------------------------------------- 3851100 Type -------------------------------------------------- Right hand helix, variable rate Material ---------------------------------------------- AISI...
  2. Dave65

    How much should machine work cost?

    For a reference this is where I had mine done. http://www.besracing.com/services.html Dave :beer
  3. Dave65

    Gear Ratios

    It is a direct relationship. 4.56 divided by 3.55 is 1.28 so you get about 28% more force (torque) transmitted to the rear wheels, which results in more acceleration. 28% is also about the difference in gear ratio for 1st to 2nd and 2nd to third for a muncie 4 speed, so the difference is about...
  4. Dave65

    Lost Steering completely tonight!

    Played golf once at Furry Creek which is along the route - a neat mountain course - very remote. The people in the club house said the bears and grizzleys were not too much of a problem but we needed to be careful, be aware of and avoid the mountain lions. They said the bears and grizzleys will...
  5. Dave65

    "whileyouareatityoumightaswellas" is a bad disease

    Barry, You made a good decision not to pull the engine or you could end up here.:D Dave :beer
  6. Dave65

    BarryK's tips on how NOT to do things.....part 1

    Barry, If it makes you feel better I learn at lot of stuff the same way.:D Dave :beer
  7. Dave65

    Where can you buy a front wheel hub

    Long Island shows them in their catalog - 49-32C - $225.
  8. Dave65

    Do you think that is really a matching numbers big block car?

    Jim, Circular machining marks may also be from resurfacing the block during a rebuild. Whether it is from this or the more questionable practice of grinding off numbers, the block in the condition you describe offers no proof as to originality. If you want to see the numbers better, use...
  9. Dave65

    Need photo of block casting date

    This is where it is located. This one stands for June (F) 14, 1965. Dave :beer
  10. Dave65

    Body lift straps?

    I will box them up over the weekend and let you the shipping early next week. Dave :beer
  11. Dave65

    Body lift straps?

    You can have my set of straps for $35 plus shipping - I am never doing that again. :D They are not light - maybe 10 pounds from 45202. Dave :d33:
  12. Dave65

    Carlisle...so who is going and where are you staying?

    John, I am looking forward to finally meeting the group - both the Vetteheads and the guys on this board. I am not sure where I am staying - I currently have two reservations at two different hotels - the Capital Plaza and one near the fairgrounds.:confused Dave :beer
  13. Dave65

    65 brake lights don't work -- help

    The obvious response is the brake pedal switch, which you did not mention. Have you check how that works? Dave :beer
  14. Dave65

    Heater feels like it is running when moving.

    The air is coming in through the cowl vents and then to the heater box. Inside the heater box are a couple of doors. One opens and closes in a way that either directs air across the heater core or around it, the other directs the air either to the heater outlets at the floor or through the...
  15. Dave65

    Looking For An '870 Block For A '65

    In response to the orginal question, in my opinion, if you want to take the original block out to save and then you plan to drive the car for fun, the most fun in a small block would be a 383 made from a 350 block. Alternatively look for a 400 block. Size and weight are the same as a 327...
Back
Top Bottom