Welcome to the Corvette Forums at the Corvette Action Center!

Search results

  1. M

    Clutch fork grinding on pressure plate!$?

    C4 LT1 6-Speed manual. Just started grinding noise when clutch pushed to floor. If you ease off, grinding noise goes away. Shifts in all gears fine, no slipping or hard shifting and no noise. Just the grind noise if clutch pushed to floor (of course this happens when not extremely careful). OK...
  2. M

    Clutch Click/grind - replacement?

    C4 1992 LT1 6-Speed manual. 60K with 20K on existing clutch. Just started grinding noise when clutch is pushed all the way to floor. If you ease off about 1/2 inch, grinding noise goes away and you hear a clicking. Ease off 3/4 inch and all noises go away. Shifts in all gears fine, no slipping...
  3. M

    Clutch Grind?

    C4 LT1 6-Speed manual. Just started grinding noise when clutch pushed to floor. If you ease off, grinding noise goes away. Shifts in all gears fine, no slipping or hard shifting and no noise. Just the grind noise if clutch pushed to floor (of course this happens when not extremely careful). Can...
  4. M

    OIL PRESSURE - $50 or $20

    C4cruiser gave me some thoughts, but still have problem. I have a 92, LT1 (P) with 60K miles. Out of the blue the analog gauge in the cluster pegged on the Hi side. No apparent high pressure symptoms from engine. After turning off, guage dropped to 80 but as soon as ignition is turned on, it...
  5. M

    Oil Pressure Gauge Pegged HI

    Have a 92, LT1 (P) with 60K miles. Out of the blue the analog gauge in the cluster pegged on the Hi side. No apparent high pressure symptoms from engine. After turning off, guage dropped to 80 but as soon as ignition is turned on, it pegs out on HI side of gauge without engine running. There...
  6. M

    Stiff shift!

    92 LT1 6 Speed. This winter the wife is finding her shifter stiffer then usual. (Her vette, Guys) Clutch OK 60K miles.. Does the bearings go or is it just the sludge like tranny fluid?? Wife is complaining :eek
  7. M

    92 6-Spd Hypertech Chip

    I have a 92 6-Spd with stock exhaust and engine, 60K miles. Would I actually get any fuel economy from installing a hypertech thermomaster chip and thermostat? Would it cause me more problems then it is worth??? Thanks.
  8. M

    Third Brake Light

    Have a 1992 LT1. Is the third (middle rectangle) brake light wired to somewhere different than the main brake lights. Mine is coming and going off at different times than the other four main lights???? If I ease off brake pedal at stop light, people tell me that the four main lights go out...
  9. M

    Relay clicking???? Help Guys!

    I have a 92 LT1 and have replaced three heavy duty batteries in last two years. Latest one is 3 month old. Garage kept. Dead battery again. It is down to 11 volt (terminal to terminal). Charger and cluster voltmeter show it charges between 14.2 and 15.2 volts, once I kick start and run it...
  10. M

    95-96 Cap and Rotor on 92 Opt Spark Distributor body. Anyone actually running this??

    opti spark 1992 (Quote:) Originally posted by RLD92 You might want to consider venting also.I went that way a little more expense but time will tell if it was worth it.I bought a new dist and a 95-96 dist cap kit 140.00+ the 350.00 newer cap fits older base and provides venting which old one...
  11. M

    FX3 Shocks (Handling/Interchangable)

    What is the difference between 89-91 and 92-95 year Bilstein FX3 shocks? They look identical. Can they be interchanged if done in pairs or would they change vehicle handling ??? ;shrug
  12. M

    FX3 Bilstein 89-91 92-95 Interchangable?

    What is the difference between 89-91 and 92-95 year Bilstein FX3 shocks? They look identical. Can they be interchanged if done in pairs or would they change vehicle handling ???
Back
Top Bottom