I'd like a shot at the 90 degree bend downward. I'm a bit confused about whether I put the weatherstriping on correctly. I took reference photos but they are not defined enough. I did it this way:
But while I went to do the other side, the weatherstriping seemed to like to be positioned...
From my "off" position (which is full clockwise), if I turn them one click positon CC they go on slow - to the next CC position they go on fast. All the plug in's can go in only one way so anyone know what is wrong? Thanks
First off, the car has been off road for 4 years. I have a 2002 battery in it that's been on a Tender all the time. I know I need a new battery when the car gets on the road especially if it doesn't power up the motor when I try and start it - which hopefully will be in the next few days.
I put...
All my other ductwork is off along with all other nuts/bolts. This is on the top left and it is holding the heater box on. I tried prying what appears to be a clip (on what appears to be a flat head rivet") off but it didn't budge. It is whats holding the box on. How does it come off - there is...
I'm cannot find specifications for this carb. I have the Rochester spec sheet but those are for GM mfg carb's with the 7 digit 702xxxx number. This carb was put on my '69 around 1974 to replace the Holly spread bore that was on it. Unfortunitly, when I bought it, it didn't have the original...
I've seen starter advertisments that say you could use "such and such" starter on SB motors with either the 150 ish or 160 ish flexplate. How can the same starter engage both a 12.x" flexplate and the larger 14" flexplate? This is probably a simple question:ugh
What are you guys that put crate motors in doing about a tachometer? Swaping a tach drive distributor in or running with an add-on unit on the steering column? Thanks, Fred
I bled the brakes on the '67 the other day:cool. When taking both front wheels off to access the bleeder screws, I noticed an abnormal "resistance" when I tried to spin the wheels:ohnoes. Now, I don't drive this vehicle too frenquently and have had it a long time. Even with front discs, the...
or should I say, lack of:L. Things have been moving along, however slowly. Yesterday I (finally) finished cleaning up and painting the frame. That is a job I don't want to do again. The gas tank is out and awaiting replacement with a new one. New body mounts and brake lines have been put in. The...
I know it cannot be done with body on frame and body off is the way to go but I'm doing body mounts, the one side at a time way, so in the process could I raise the passenger side enough to get the lines on without cutting them? I've done the brake lines without too much cursing. Doing the lines...
After raising the D/S and cleaning up the frame, the line up for #1 isn't exact. In the photo below, the mount is positioned properly but the body hole where the bolt goes thru is off. Can I just move the mount to match the hole in the body bracket? But then the protrusion will be sitting on the...
These are metal not aluminum. Thought these might be the best alternative over rubber or poly. It's a street car and any added harshness wouldn't be an issue with me. Anyone tried these? Thanks as always, Fred:)
- Guldstrand Motorsport
Any experts out there:confused. For someone who hasn't done it before;shrug, how long would you expect :chuckle this person to get the old front clip off and then how long to hang a press molded (3 section, top surround, + fenders) replacement. Exclude pre-prep and paint time on the new section...
Well finally after getting these in (from Fort Wayne Clutch) along with my emergency brake job, the rear wheels are all cocked. The driver side isn't too bad (it may even be correct) but the pass. side is all ****** up. I drove it a bit and it appears it got slightly better but it's out of wack...
At the Greenwich Concours yesterday and the car went for $90K plus buyers premium which I took as a "good deal" for the buyer if the car was what it said it was - an original numbers matching fuelie. No real interest show by the bidders which I think there were only 2 bidding on it.
My '69 has been temporarily displaced from the garage due to another car purchase. I've seen Canvas type "temporary" garages while on vacation traveling but now that I want one, can't seem to find where (an internet site perhaps) to buy a "good" one. Pep Boys sells a 10x20 (my cousin bought...
I would like to put back my '69 as original. I've had the custom nose on it since the mid 70's but my tastes have changed and I think I now want the pop ups back. My question(s) are:
1. Can I just take the molding strip off and attach the top hood press molded surround piece and put on a new...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.